1.排除空氣，隨著卷材滾動按壓，并擠壓卷材中的空氣，使卷材穩固粘合。

1. Remove the air, press and squeeze the air in the roll as it rolls, to ensure stable adhesion of the roll.

2.鋪設彩鋼瓦卷材時，應從流水下坡方向開始施工，立墻面由高到低鋪設。

When laying color steel tile rolls, construction should start from the downhill direction of the flowing water, and the vertical wall should be laid from high to low.

3.卷材搭接長邊為3cm-8cm，短邊為10cm。

3. The lap length of the coil is 3cm-8cm, and the short edge is 10cm.

4.當溫度較低時，基層和卷材必須同時涂刷基層處理劑。

When the temperature is low, both the base layer and the roll material must be coated with base treatment agent at the same time.

5.外露卷材短邊搭接、卷材收頭及異性部位處應用密封膏密封。卷材立墻收頭用金屬條固定在預留槽內，然后用密封膏密封。

5. The short edge overlap of the exposed coil, the end of the coil, and the opposite parts should be sealed with sealant. The end of the coil wall is fixed in the reserved groove with a metal strip, and then sealed with sealant.

施工中影響彩鋼板質量的關鍵因素還是材料的好壞，只有先保證材料質量，施工才能保證。洛陽市冠朝彩鋼有限公司成立于2009年，目前公司有的凈化板、巖棉板、硅巖板、玻鎂板、EPS夾芯板生產線、單層彩鋼瓦生產線。板型有760、840、900、740、343等板型，可生產0.3mm-1.0mm厚彩鋼卷，有輕鋼龍骨生產線，可生產0.8mm-3.0mm厚、80mm-300mm寬的超大型輕鋼龍骨設備，900型樓承板、有鋼構件加工拋丸除銹設備，并設計、安裝鋼構工程、輕鋼別墅工程。

The key factor affecting the quality of color steel plates during construction is still the quality of the materials. Only by ensuring the quality of the materials can construction be guaranteed. Luoyang Guanchao Color Steel Co., Ltd. was established in 2009. Currently, the company has production lines for purification panels, rock wool panels, silicon rock panels, glass magnesium panels, EPS sandwich panels, and single-layer color steel tiles. There are plate types such as 760, 840, 900, 740, 343, which can produce color steel coils with a thickness of 0.3mm-1.0mm. There is a light steel keel production line that can produce ultra large light steel keel equipment with a thickness of 0.8mm-3.0mm and a width of 80mm-300mm. There is also a 900 type floor support plate and steel component processing shot blasting and rust removal equipment, as well as the design and installation of steel structure engineering and light steel villa engineering.